eCFR Reference Browser

---

title: "40 CFR §1065.695"

source: "https://www.ecfr.gov/current/title-40/section-1065.695"

title_number: "40"

volume_number: "37"

chapter_number: "Unknown"

subchapter_code: "U"

subchapter_subject: "AIR POLLUTION CONTROLS"

part_code: "1065"

part_subject: "ENGINE-TESTING PROCEDURES"

subpart_code: "G"

subpart_subject: "Calculations and Data Requirements"

section_number: "1065.695"

section_subject: "Data requirements."

cfr_reference: "40 CFR 1065.695"

title_name: "Title 40"

title_subject: "Protection of Environment"

parts_covered: "Part 1060 to End"

revised_date: "Revised as of July 1, 2019"

publication_date: "As of July 1, 2019"

contains_description: "Containing a codification of documents of general applicability and future effect"

publication_info: "Published by the Office of the Federal Register National Archives and Records Administration as a Special Edition of the Federal Register"

---

(a)To determine the information we require from engine tests, refer to the standard-setting part and request from your Designated Compliance Officer the format used to apply for certification or demonstrate compliance. We may require different information for different purposes, such as for certification applications, approval requests for alternate procedures, selective enforcement audits, laboratory audits, production-line test reports, and field-test reports.

(b)See the standard-setting part and § 1065.25 regarding recordkeeping.

(c)We may ask you the following about your testing, and we may ask you for other information as allowed under the Act:

(1)What approved alternate procedures did you use? For example:

(i)Partial-flow dilution for proportional PM.

(ii)CARB test procedures.

(iii)ISO test procedures.

(2)What laboratory equipment did you use? For example, the make, model, and description of the following:

(i)Engine dynamometer and operator demand.

(ii)Probes, dilution, transfer lines, and sample preconditioning components.

(iii)Batch storage media (such as the bag material or PM filter material).

(3)What measurement instruments did you use? For example, the make, model, and description of the following:

(i)Speed and torque instruments.

(ii)Flow meters.

(iii)Gas analyzers.

(iv)PM balance.

(4)When did you conduct calibrations and performance checks and what were the results? For example, the dates and results of the following:

(i)Linearity verification.

(ii)Interference checks.

(iii)Response checks.

(iv)Leak checks.

(v)Flow meter checks.

(5)What engine did you test? For example, the following:

(i)Manufacturer.

(ii)Family name on engine label.

(iii)Model.

(iv)Model year.

(v)Identification number.

(6)How did you prepare and configure your engine for testing? Consider the following examples:

(i)Dates, hours, duty cycle and fuel used for service accumulation.

(ii)Dates and description of scheduled and unscheduled maintenance.

(iii)Allowable pressure range of intake restriction.

(iv)Allowable pressure range of exhaust restriction.

(v)Charge air cooler volume.

(vi)Charge air cooler outlet temperature, specified engine conditions and location of temperature measurement.

(vii)Fuel temperature and location of measurement.

(viii)Any aftertreatment system configuration and description.

(ix)Any crankcase ventilation configuration and description (e.g., open, closed, PCV, crankcase scavenged).

(x)Number and type of preconditioning cycles.

(7)How did you test your engine? For example:

(i)Constant speed or variable speed.

(ii)Mapping procedure (step or sweep).

(iii)Continuous or batch sampling for each emission.

(iv)Raw or dilute sampling; any dilution-air background sampling.

(v)Duty cycle and test intervals.

(vi)Cold-start, hot-start, warmed-up running.

(vii)Absolute pressure, temperature, and dewpoint of intake and dilution air.

(viii)Simulated engine loads, curb idle transmission torque value.

(ix)Warm-idle speed value.

(x)Simulated vehicle signals applied during testing.

(xi)Bypassed governor controls during testing.

(xii)Date, time, and location of test (e.g., dynamometer laboratory identification).

(xiii)Cooling medium for engine and charge air.

(xiv)Operating temperatures of coolant, head, and block.

(xv)Natural or forced cool-down and cool-down time.

(xvi)Canister loading.

(8)How did you validate your testing? For example, results from the following:

(i)Duty cycle regression statistics for each test interval.

(ii)Proportional sampling.

(iii)Drift.

(iv)Reference PM sample media in PM-stabilization environment.

(9)How did you calculate results? For example, results from the following:

(i)Drift correction.

(ii)Noise correction.

(iii)“Dry-to-wet” correction.

(iv)NMHC, CH4, and contamination correction.

(v)NOX humidity correction.

(vi)Brake-specific emission formulation—total mass divided by total work, mass rate divided by power, or ratio of mass to work.

(vii)Rounding emission results.

(10)What were the results of your testing? For example:

(i)Maximum mapped power and speed at maximum power.

(ii)Maximum mapped torque and speed at maximum torque.

(iii)For constant-speed engines: no-load governed speed.

(iv)For constant-speed engines: test torque.

(v)For variable-speed engines: maximum test speed.

(vi)Speed versus torque map.

(vii)Speed versus power map.

(viii)Brake-specific emissions over the duty cycle and each test interval.

(ix)Brake-specific fuel consumption.

(11)What fuel did you use? For example:

(i)Fuel that met specifications of subpart H of this part.

(ii)Alternate fuel.

(iii)Oxygenated fuel.

(12)How did you field test your engine? For example:

(i)Data from paragraphs (c)(1), (3), (4), (5), and (9) of this section.

(ii)Probes, dilution, transfer lines, and sample preconditioning components.

(iii)Batch storage media (such as the bag material or PM filter material).

(iv)Continuous or batch sampling for each emission.

(v)Raw or dilute sampling; any dilution air background sampling.

(vi)Cold-start, hot-start, warmed-up running.

(vii)Intake and dilution air absolute pressure, temperature, dewpoint.

(viii)Curb idle transmission torque value.

(ix)Warm idle speed value, any enhanced idle speed value.

(x)Date, time, and location of test (e.g., identify the testing laboratory).

(xi)Proportional sampling validation.

(xii)Drift validation.

(xiii)Operating temperatures of coolant, head, and block.

(xiv)Vehicle make, model, model year, identification number.

§1065.695 - Data requirements.